Double Glazing Door Lock Repairs
Is your uPVC window or door mechanism broken? Perhaps the window or door handles don't meet up properly or are hard to use.
It is essential that your double glazed doors operate smoothly, otherwise you'll lose energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.
Snapped Key
It can be frustrating when a key gets stuck into the lock. This can also be a security issue because it could make you vulnerable to burglars if your door is not locked. Fortunately, there are some quick fixes you can use to solve the issue and get your door functioning correctly.
The first step is to remain calm. If you get scared and start poking around wildly, you might just end up pushing the damaged piece of the key deeper into the lock, making the situation much worse.
Next spray WD-40 or another penetrating oil into the lock to help the broken piece slip out more easily. You can also use a screwdriver to break any pieces that are stuck. If you happen to have a little bit of the key that is sticking out and you want to remove it, make use of a paperclip, or any other metal object with a thin surface to grab it and then pull it out. Both methods are effective, but you need to be careful not to push the damaged key piece further into the keyway.
Some paperclips have grooved edges that could serve as hook extractors and Jigsaw blades can also be used for this function. If you don't happen to have any of these items, you can bend a hook with needle-nosed pliers. Additionally, you can use a pair of tweezers grab and remove the last piece of broken keys.
If you are unable to remove the broken key piece, use a lock deicer. This is usually found in most hardware stores. It works by freezing any moisture or ice that may be inside the lock.
If none of these solutions work, it might be time to call a locksmith. Fitlocks experts can quickly solve problems like broken handles or snapped keys with uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms to ensure that they are more easy to use. Request a repair for your double glazing through us online or give us a phone call to discuss your requirements.
Broken Cylinder
A broken cylinder can be a serious security risk. A professional locksmith is able to repair the cylinder. To fix the cylinder a locksmith will need to tap it. They can do this using a hammer or other tool, but the most efficient way is to employ a long match or piece of wire. Place the match or wire's end close to the keyway. After this, the locksmith can strike the lock and break it open. This is better than using a hammer, which can harm the lock.
Overheating is the primary cause of cylinder heads cracking. This can happen when the cylinder block and cylinder head are made of various metals, such as cast iron and aluminium. When the different metals are heated and cool at different rates, it may cause localised hotspots that expand faster than the rest of the cylinder head, leading to cracks.
Corrosion is a different cause of cracks in the cylinder. If the head and block of the cylinder are not maintained properly they may be corroded or rust, which can cause them to expand faster than anticipated. Over time, this can cause cracks.
If your uPVC door or window lock is brittle or requires lots of pressure to turn, it can be caused by many things. A defective locking mechanism, misalignment or an old handle are the most common reasons for this issue.
It is a quick and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith will typically be able to solve the issue within an hour of arriving at your property. They can fix the locking mechanisms, or replace the window handles and replace the gearboxes, based on your specific needs. A professional locksmith will be able to inform you of the most cost-effective option for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders that offer an additional layer of protection from burglars. It's a small price to pay for the peace of mind that comes from knowing that your uPVC doors are secure.
Broken Handle
It's not a surprise that window handle locks may break. They have complex mechanisms which deteriorate over time. It isn't easy to determine the cause of the problem and repair it correctly.
If the issue is in the internal locking mechanism or the latch, fixing your broken handle will increase your uPVC double glazing door's security and allow you to stop drafts. It can be expensive to repair or replace your handle incorrectly and it double glazed window repairs near me can also harm the frame and lock of your door.
Screwdriver: With the window open remove the screw that holds the handle. It double glazing company near me should be located on the inside of the back plate, and is normally covered by an aesthetically pleasing cover for the screw reasons. You should not lose any internal parts of the handle like the levers and plates on either side. Ideally, keep these in the same order so that you can replace them in the event of a double glazed near me need.
Then, with another screwdriver, loosen the screw that connects the handle to the spindle at the back. Once this is loose, you should be in a position to pull the handle away and pull off the damaged spindle. double glazed units near me Replace it with a brand new spindle, ensuring it's the same length (you can find them online or in hardware stores). Securely screw it into place. Be careful not to overtighten as this could cause damage to the handle or the window frame.
Ensure the new handle is fitted after which you can close and test the handle. The hope is that it will function smoothly and you'll be able to unlock your window.
While you're working on the handle, be sure to make sure your uPVC windows are shut properly. If they're not, click here you could experience damp and draughts inside your home, as in addition to compromising your home's energy efficiency. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure that they close properly.
Broken Spindle
It is usually the case that the spindle within the handle is broken, not the handle itself. This is especially frequent in uPVC tilt and turn windows. These windows require a handle which acts as a locking mechanism within the frame of the window. The handle is attached a central rod that triggers the locks that are shaped like mushrooms and lock into the window frame keep. If the dead latch mechanism fails to open when the handle has been turned, it's likely the spindle is damaged. This can be a problem that is frustrating.
Luckily, there are steps that can be taken to fix this problem. A good locksmith can quickly and efficiently fix this problem. A professional locksmith can disassemble the window's handle using a tool to take out the wheel from the area where the spindle is located. This can be done without damage to the handle or window frame.
After removing the wheel the technician can examine the spindle to determine what caused it to break. This involves disassembling the spindle and inspecting each component part, noting any wear or damage. This process is usually performed by technicians in an environment that is clean.
The next step is to clean the damaged spindle, this helps eliminate any debris or dirt that might be obstructing its normal functioning. The spindle could be repaired or replaced. If it's being replaced, the technician can take a dowel of a similar size to the one used in the first and drill mating holes into both pieces of the spindle. This will ensure that the spindle will fit perfectly with the handle.
If the damaged spindle can't be repaired, it could need to be replaced entirely. Home centers can sell generic replacements however if your window design is unique you'll require contacting an expert in woodworking or cabinet making who can recreate the exact part. Once the spindle has been installed, it is attached to the handle. The screw holes on the handle with the screws that are already in the frame. Once the new handle is seated you will be ready to operate your uPVC window.